Important: Our new home for AFM probes is launching. The US and Canada is now served at . Australia, India, Singapore, South Korea, and Taiwan are served at . You must create a MyOI account to use the store, instructions here . If you have any questions or concerns please contact:


Product was successfully added to your shopping cart.



Quick Overview

Quartz-like material probe with carbon EBD tip for high speed imaging in tapping/non-contact mode.

To be used only on AFMs with small laser spot

f = 2000 kHz   |   k = 3 N/m   |   tip coating: none

製品 単価 個数
USC-F2-k3 (10 Pack)
(Ships in 1-2 Weeks)


Ultra-Short Cantilevers (for High-Speed AFM)
NanoWorld Ultra-Short Cantilevers (USC) for High-Speed AFM (HS-AFM) combine very small cantilevers capable of resonating in the MHz regime and a very sharp and wear resistant tip.
The cantilever of the USC series is rectangular and made of a quartz-like material. A gold layer is deposited on both sides of the cantilever in order to enhance the reflectance of the laser beam, but the tip remains uncoated.
The wear resistant tip has been developed together with nanotools GmbH and sustains high velocity scans over long distances. It is made of High Density Carbon/Diamond Like Carbon (HDC/DLC) material which is hard and wear resistant. It has a height of 2.5 microns and a radius of curvature smaller than 10 nm. The aspect ratio is in the order of 5 : 1 and the tilt compensation is 8° ensuring more symmetric AFM images.
The silicon support chip is of standard dimensions (1.6 mm x 3.4 mm x 0.3 mm). Additionally, it has etched and lowered corners in order to avoid contact between the support chip and the sample when scanning. Moreover it features alignment grooves on the back side of the silicon support chip which ensure replacement of the probes without major adjustment of the laser beam when used in conjunction with the alignment chip.
The type USC-F2-k3 is mainly designed for High-Speed AFM applications in non-contact mode in air but can also be used for other applications.

Gold Reflex Coating
The gold reflex coating consists of a 30 nm thick gold layer deposited on both sides of the cantilevers which enhances the reflectance of the laser beam. Furthermore it prevents light from interfering within the cantilever. As the coating is almost stress-free the bending of the cantilevers due to stress is less than 2 degrees

The tip remains uncoated.
System limitations: due to their small cantilever sizes and their very high resonance frequencies USC probes currently cannot be used in all commercially available SPMs and AFMs. Only AFMs with a sufficiently small laser spot and electronics that are capable of dealing with high resonance frequencies of up to 5 MHz are able to work with the USC probes. If in doubt whether these probes can be used in your AFM please check back with us or with your AFM manufacturer."

Cantilever Specifications
Spring k (N/m) 3 (0.9 - 10)
Freq (kHz) 2000 (1500 - 2500)
Length (µm) 10 (9.5 - 10.5)
Width (µm) 5 (4.7 - 5.3)
Thickness (µm) 0.3 (0.2 - 0.4)
Shape rectangular
Material Silicon
Reflex Coating (nm) Cr/Au (5/30)

Tip Specifications
Tip radius (nm) 10 +/- 3
Tip height (µm) 2.5 +/- 0.5
Front angle (°) 8 +/- 1
Back angle (°) 8 +/- 1
Side angle (°) 8 +/- 1
Tip shape cone
Tip material Carbon
Tip coating (nm) none

Untitled Document

Additional Information

Tip Radius 10
Tip Radius 5-10 nm
Spring Constant 3
Frequency 2000
Compatibility blueDrive
Manufacturer Nanoworld

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

  1. このプローブのレビューを書く

Write Your Own Review

Only registered users can write reviews. Please, log in or register